Rate Card Admin - Advanced Tab
Configure Advanced Rate Card billing rules, global markups, overrides, Rep Defaults, and engineer profile labour rates.Details
Admin Setup – Advanced Tab & Engineer Rates
The Advanced tab is available exclusively inside My Company → Rates for users with Advanced Pricing permission. It contains two sub-tabs—Global Billing & Overrides and Rep Defaults—that drive how automated Job Ticket financials calculate once Sync Job Financials is switched On.
Key Takeaway – Quick-Start Rep Defaults vs Individual Engineer Profiles: Entering Rep Defaults gets automated job costing working immediately across the whole team. However, best practice is to enter each engineer’s specific rates in My Company → Users—and note that an engineer’s Salary must be set above £0.00 for their individual Labour panel to apply instead of Rep Defaults.
Real-Life Use Examples
Typical ways administrators configure the Advanced tab:
- Scenario 1 – Enforcing Minimum Charge, Rounding & Markups: An admin sets a 1 Hour Min Charge, 15 Minutes Rounding, 35% Labour Markup, and 25% / 45% PO Markups (Low/High) so every billable job automatically applies consistent margins without manual spreadsheet checks.
- Scenario 2 – Setting Rep Defaults & Promoting Senior Engineers: On go-live day, an admin enters a £30.00 Standard Rate and 08:00–17:00 hours in Rep Defaults, then opens two senior engineers’ profiles under My Company → Users, sets their Salary above £0.00, and assigns them a higher £42.00 hourly rate.
Step-by-Step Instructions
- Open the Advanced Tab & Choose Rate Fallback Behaviour: Go to Profile Navigation → My Company → Rates and click the Advanced tab. On the default Global Billing & Overrides sub-tab, set Enable Rate Fallback: leave it Off (recommended) for strict customer-level pricing where missing prices remain £0.00, or switch it On to cascade missing Site/Managing Agent prices up to My Company and use Job Rate overrides as an engineer failsafe.

Screenshot 1: Advanced tab sub-navigation and Enable Rate Fallback toggle.
- Configure Global Billing & Markups: In the left-hand panel (Global Billing & Markups—applied automatically to all jobs):
- Min Charge: Choose Not Set, 30 Minutes, 1 Hour, 2 Hours, or 3 Hours to set the minimum billable labour duration.
- Rounding: Choose Not Set, 15 Minutes, 30 Minutes, 45 Minutes, or 1 Hour (applied after Min Charge).
- Markups: Enter whole-number percentages for Labour Markup (%), Travel Markup (%), PO Markup Low (%), and PO Markup High (%).

Screenshot 2: Global Billing & Markups panel.
- Configure Rate Card Overrides (For Fixed Job-Level Hourly Overrides): In the right-hand panel (Rate Card Overrides), set Standard Time Start, Standard Time End, Initial Rate Lock, Sat Overtime (All day), Sun Overtime (All day), Overtime (%), Public Hol (%), and Billable Travel (%). Remember that these rules only activate on jobs whose Job Rates row specifies a Rate above 0.00.

Screenshot 3: Rate Card Overrides panel.
- Set Quick-Start “Rep Defaults”: Switch to the Rep Defaults sub-tab. Under Default Rates & Multipliers, enter your fallback Standard Rate, Overtime (%), Public Hol (%), and Travel (%). Under Default Working Hours & Rules, select Standard Start and Standard End (ensuring End is later than Start), and toggle Rate Lock, Sat Overtime, and Sun Overtime.

Screenshot 4: Rep Defaults sub-tab settings.
- Configure Individual Engineer Profiles (Recommended Next Step): Once your company-wide defaults are saved, go to My Company → Users and open each engineer’s profile. Enter their Salary (which must be greater than 0.00) and complete their Labour panel (Standard Rate, Overtime %, Public Hol %, Travel %, Standard Start, Standard End, Sat Overtime, Sun Overtime, and Rate Lock). Any engineer whose Salary remains at 0.00 will continue using Rep Defaults.

Screenshot 5: Engineer user profile showing the Salary field and Labour panel.
Variations & Conditional Rules
- Public Holiday Precedence: Public Hol (%) overrides both standard weekday hours and weekend (Sat / Sun Overtime) rules on recognised Bank Holidays.
- Initial Rate Lock / Rate Lock: When enabled, if an engineer starts a visit inside standard working hours, the entire visit stays at the standard rate even if it finishes in overtime; when disabled, the visit splits automatically into standard and overtime portions.
- Auto-Save Behaviour: All dropdowns, switches, and inputs on both sub-tabs auto-save immediately upon change (or on blur/Enter for text/numeric fields), except Rep Defaults start/end time changes if validation fails.
- Strict Access Control: Users without Advanced Pricing permission see the Advanced tab greyed out on My Company, and non-admin staff on Managing Agent, Site, or Job Ticket records never see it at all.
Field Rules & Validation Messages
| Field Name |
Requirement & Rules |
On-Screen Warning / Error Message |
| Standard Start & Standard End (Rep Defaults) |
Standard End must be strictly later than Standard Start; invalid selections revert and do not save. |
“Default Standard End Time must be later than Default Standard Start Time.” |
| Standard Rate (Rep Defaults) |
Currency decimal up to 7 characters (blank resets to 0.00). |
None. |
| Markup & Multiplier Percentages |
Whole integer percentages (blank resets to 0); for example, 150 equals time-and-a-half and 200 equals double time. |
None. |
| Advanced Tab Access & Save |
Requires Advanced Pricing Settings permission on My Company. |
“You do not have permission to access Advanced Pricing Settings.” / “Unable to save Rate Card changes.” |
Frequently Asked Questions
Why can’t I see the Advanced tab, or why do I get a permission message when clicking it?
The Advanced tab is only displayed when opening Rates from My Company, and opening it requires the Advanced Pricing Settings user permission.
I entered individual rates on an engineer’s profile, so why is the system still using Rep Defaults?
Check the engineer’s Salary field under My Company → Users. Whenever Salary is £0.00, the costing engine treats the engineer as having no individual profile costing and automatically uses Rep Defaults.
Why are my Rate Card Overrides settings not applying to a Job Ticket?
Rate Card Overrides only apply when the matching Job Rates row has a fixed hourly Rate entered above £0.00. If Rate is left at £0.00, the engineer’s profile settings (or Rep Defaults) govern standard hours, overtime, and travel.
Should I switch Enable Rate Fallback On or leave it Off?
The recommended setting is Off for stricter, predictable pricing (missing customer rates clearly result in £0.00 so gaps are spotted immediately). Switch it On only if you want missing Site or Managing Agent prices to fall back automatically to My Company defaults.
See Also:
Rate Card Admin - Advanced Tab
Check out the other 'How To' guides to find out more about Workforce Manager.
If you would like to know more about AutoVu and what we can do to help your business, why not check out our Frequently Asked Questions page, or Contact Us any time to discuss your specific requirements.
Professional cloud based software